NCP Industries ADORN Stone Shadowledge Series Pillar Stone

ADORN Stone Shadowledge Series Pillar Stone is a mortarless stone veneer system that installs 3x faster than traditional stone using a screw-on fastener system. At 6 inches tall by 18 inches wide and 1.75-1.8 inches deep, these lightweight panels transform a basic 14x14 inch frame into an 18x18 inch finished pillar without needing a mason.

The standout feature? CaptureCrete technology that captures approximately 1.5 lbs of CO2 per square foot and avoids about 1 lb of CO2 per 21 square feet during manufacturing. That’s not greenwashing — it’s measurable carbon reduction that contributes to LEED points and carbon credit eligibility.

Installation Speed and Structural Benefits

The 3x faster installation compared to traditional stone comes from eliminating mortar completely. No mixing, no mess, no waiting for cure times. You screw panels directly to the substrate using corrosion-resistant exterior screws with minimum 3/8 inch heads. The fasteners need to be 1.5 to 1.75 inches long and must penetrate studs by at least 1 inch.

Each box contains 4 pieces covering 2 square feet or 1.5-2 linear feet. For Montana contractors dealing with short construction seasons, that speed matters. You’re not racing temperature drops to get mortar to cure properly.

The weight advantage is huge for structural calculations. At under 15 lbs per square foot (typical for this stone veneer type), you avoid the reinforcement requirements of full-depth stone. That’s particularly valuable when adding stone to existing structures where the foundation wasn’t originally designed for heavy cladding loads.

Pillar Construction Specifications

Here’s where the math gets specific. You build a 14x14 inch outside dimension frame using 2x2s or 2x4s with OSB or plywood. That frame, once wrapped with the Pillar Stone, creates an 18x18 inch finished pillar.

Specification	Value
Panel Dimensions	6”H x 18”W x 1.75-1.8”D
Frame Requirement	14” x 14” outside dimension
Finished Pillar Size	18” x 18” outside dimension
Coverage per Box	2 sq ft / 1.5-2 linear ft
Pieces per Box	4 pieces
Fastener Length	1.5-1.75 inches
Fastener Head	Minimum 3/8 inch diameter

Before installation, cover the frame with ice and water resistant wrap (WRB), with 15 lb felt recommended as an additional layer. Then screw panels directly to substrate following the Pillar Stone Installation Guide for corner alignment.

Environmental Impact and Material Composition

The panels use manufactured stone veneer (concrete based) with proprietary CaptureCrete technology for CO2 absorption and neutralization, incorporating recycled and sustainable materials. The CaptureCrete technology actively captures and permanently stores CO2.

This isn’t just marketing fluff. Each square foot captures approximately 1.5 lbs of CO2, with the manufacturing process avoiding about 1 lb of CO2 per 21 square feet. For a typical residential project using 500 square feet of stone veneer, that’s 750 lbs of CO2 captured.

The product holds a Class A fire rating (standard for concrete-based manufactured stone veneer) — critical for Montana’s wildfire-prone regions. Available colors include Colorado Gray (Limestone), Sandstone, Slate, and Northern Gray.

The Limited Lifetime Warranty covers manufacturing defects only, providing replacement of defective material at no charge. It excludes structural movement, discoloration from chemicals or paint, natural elements (hail, wind, sun), improper installation or fasteners, labor costs and consequential damages. The warranty is non-transferable and applies to original purchaser only.

Frequently Asked Questions

Q: Can I install this product myself or do I need a mason?

The screw-on fastener system makes it DIY friendly with no mason needed. Installation is 3x faster than traditional stone with no mortar mess or drying time required. Basic carpentry skills and the ability to follow the installation guide are sufficient.

Q: What size pillar frame do I need to build?

Build a 14x14 inch outside dimension frame using 2x2s or 2x4s with OSB or plywood. This creates an 18x18 inch finished pillar when wrapped with the stone.

Q: How much CO2 does this product actually capture?

Each square foot captures approximately 1.5 lbs of CO2, and the manufacturing process avoids about 1 lb of CO2 emissions per 21 square feet compared to traditional concrete.

Q: What’s included in the warranty?

The Limited Lifetime Warranty covers manufacturing defects only, providing replacement material at no charge. It excludes damage from structural movement, chemicals, natural elements, improper installation, and all labor costs. Non-transferable to subsequent owners.

Q: Can this connect to other ADORN products?

Yes, it’s compatible with ADORN Flat panels for contiguous wall-to-pillar transitions, plus ADORN accessories including corners, sills, and outlet boxes.